Anglo Traction

I'm always grateful Alan and thanks. If the Topic/thread provides interest and something to read/look at being produced, then it has served it's purpose. Interests vary and is always good to see them all in material forms such as on this Forum, irrespective of varying skill levels and subjects. Reckon you're right Norm. They are obscured by the wheels. Only needed a few thousands of an inch variation on the flatness of the retaining plate while heating up for the lettering to be able to shift. Humbled John. Thanks. Learned to love the qualities of metals and lucky to have lots of patience. Things take me a long time to do, what with learning as I go. A project to me is loads of smaller projects which combine to make a finished one, hence the slow pace. Happy with the progress and the finished item is in sight Regards Well I somehow endured the low temperatures and managed to get some colour on this Water Cart. Matt finish is important as it seems to improve the appearance of a model this size. I had to use 2 different primers, one on the metal parts and another on the wood. Top coat went on fine with only a few undesirable bits in it which were easy to remove after. I used my 45 year old Badger 200 Airbrush, which had done many Murals on Car and Van panels back in the 1970s and still going strong- Once dry, I was able to pick out the raised lettering in yellow, a challenge with a tiny 6 bristled sable brush and an Eye Glass, while holding my breath to keep my hand steady- Currently a partial assembly to keep the bits together and dust free- Colour variations are due to available light, but the last image is what the colour is by eye. Valve internal parts now fitted. Matt varnish for top coat is on order. Currently dulling off the shiny wheel rims using acid to etch the finish. Regards

I bought a basic Martek Drill Sharpener back in 1986, attaches to an electric drill and fixed into a drill holder back in that period. Only covered bits from 1/8" upwards. Still have it, but not used much. I tend to dispose of, or sharpen by hand, any bits under 1/8" and use only for wood after. Although I was successful in hand sharpening 2 off 1/32" drill bits after I broke them while working on my latest project. To be on the safe side, I started the hole with a good one, then followed up with the sharpened one and went fine with no issues. Winter 'clips my wings' with projects due cold workshop and other priorities. Like you're having to do, I do much of small work on the table in the warmer conditions. The other thing keeping me busy is learning the secrets of a different OS from Windows to MacBook Pro after 15 years using Microsoft.

Hello all, and thanks for the positive comments. Finally got to a point where I could get the tank primed during a dry and low humidity weather window. Had been busy making the (tiny) tank lid furniture out of mainly Nickel Silver. The latch bolts are 3/64" (1.2mm) dia silver steel with 1/16" (1.56mm) stainless balls brazed on and fixed with 1/32"(0.8mm)rivets- Next job is permanently fix the woodwork to the tank and finish ready for paint Not completely successful with the soldered lettering, as a couple had moved slightly in the process...never mind!, just glad to get past this stage- I really need good, dry painting weather now, as I have to paint and assemble this and the T/Engine to fix the dimensions for the towing bar frame for the Water Cart. Regards.

Hello again all, Long time, no post !. I've been busy during this absence, honest !. Lots of preparation for painting the T Engine, only managed to get to the etch primed stage on most parts. Temp, weather and humidity has halted progress. I have been working on the Water Cart for some time. Glad to have finished the 130 holes for the 1/32" (0.80mm) rivets. Broke 2 drill bits and had to get the pieces out by dissolving them over a few weeks. Have reproduced the raised 'cast in' lettering on each of the tank ends by individually soldering them in place after fitting and sealing the tank end plates in position. The letters are 3mm and 2mm in height and had to make the Ampersand out of bits- Just finished making and trial fitting the wooden board work, tank lid and have revised the pump outlet nozzle . The latch bolts are under way, with just the handle to make before fitting. So just waiting for a 'weather window' to get the 2 part etch primer on- Regards

Interesting that you say it's ATCO. I never knew they produced such an item !. I see the tank is an adapted standard ATCO. Could do with a few more pics of the engine. May be the Mk1 79cc version?. Is it water-cooled?. Looks direct drive with only 2 blades on the propellor. Carb looks like a V508c/1. Can't remember if the needle taper/jet size is the same on both versions. Villiers Midget MK2/3 Manual is in the Downloads section (on the header line in Home page). if it is the 79cc version, I should be able to obtain some info, but not immediately.

No problem, If one of the old ones are repairable, PM me a photo of it's condition. If it's possible to fix, you're able to send it to me and cover the postage, I'll see what I can do. ...............bit slow.... Wristpin beat me to it.

Hope the reliability endures in the new one Norm and gives you many miles trouble free

If you have no luck Ray, and your examples are not able to bve refurbished (mechanically), then a new replacement is available if you're desperate, but looking at about £30 delivered !. Regards Richard

Hi Stewart, Welcome, Not too familiar with that model in U.S. Although there are quite a few around in the UK. A quick search of the make revealed a Website Farmcollector.com which has an example (amongst many) of your version. I'm sure is much knowledge and info available from those owner/members. Good quality, looking and efficient machines. Like to know how you get on. Regards

Hi Ray, Just checked Jacks small engines online with your engine type number -LINK- And the Parts Manual (1979) I have for that engine model It shows the Gasket Set part number to be 299577 ?. My old 'Osprey' thread is in the 'Other Garden Machines' Forum section if it is any help for reference. - OSPREY- Regards

I have to admit, I do like these little O&R engines and the tooling they design for them to power. Not a fan of Chainsaws, but I like my little 71 Baird Poulan. Your project subject looks interesting. Is the saw chain 1/4" pitch and the blade 12" ?. Also looks to have a manual oil pump?. Regards

No shame in going Yellow Mark!. Always liked these myself. Hope all's well. I think the giveaway in finding the right spec of K241 is the effort someone has gone to in shoehorning and chopping out to fit that engine. The correct spec is K241-a (not 241s) spec should be 46700d and used the delco remy starter gen. Then again I'm no expert, but the mating of the engine to the drive is the relevant bit. I suppose it depends if you're planning to put it back to close original?. Good to see some more build projects on here though. I'll check in more often. Regards.

Excellent work Ewan, well done !.

Superb job on that Nigel . Even more of an acheivement when it looks like it still has a V70 Techy with a series 1 Lauson carb! and you get it running sweetly.

Hi all, thanks for the positive responses. Certainly a different way of working when producing scale models without plans or castings etc. Everything takes longer and a lot of thinking. Managed to reach a point of trial fitting the spray bar parts today which I've been working on for a while- I stripped the chrome off of a 60s car aerial section which was the right size in hard straight brass (5/32" or <4mm). I failed with reproducing the flanged connecting pipe, as it should be straight and I had to 'dog leg' it to line up. Probably as a result from having to work from a basic drawing for sizes of a similar make of cart. Still, it's a reasonable representation until I can get to M.E.R.L to inspect the company's original drawings. The retaining brackets were an excercise in miniature milling and retained with 12ba coach bolts/nuts- Time to start drilling loads of tiny holes............I may be some time !. Regards

Very nice (jigsaw) project you have there Nigel !. I'm impressed that your Blaster/Powder Coat man takes the trouble to wrap/protect all the parts for return.

You/Mark were my next port of call as a suggestion to Angus, as I remember the project Ewan .

Maybe worth checking again with Nigel. Looks the same size as fitted to H50/60,V70 etc (31715) - . I had to obtain missing parts from the states 9 years ago for this derelict H60 Rotavator as no availability in UK (used or new)- Nigel's V70 Lawn Ranger... looks pretty close without checking parts lists - Good luck with sorting it.

Thanks Norm, Nigel. Soldered the 2 halves of the tank together, but left the end plates for now, as need access. Much of the work over the last 6 weeks has been doing fiddly parts. Because this project is all 'Scratch Built'', I want to keep the parts as scale size to the original. The water outlet/valve is an example and is a simple 'Bottle' style valve running in guides. The joint faces are metal to metal (no seals)- The faces that contact the inside/outside of the tank are contoured to a close fit. The weighted lever sits 'over centre' when closed, which applies pressure on the Spring Stainless rod and so on the valve face/seat to improve the water tight seal. Another view to show the valve/seat and the fabricated outlet with correctly bolted (12BA) flange. This will lead to a Sprinkler Bar as per original- Hardwood support legs finished to size. A range of steel coach bolts with square/hex nuts, and an alternative flanged outlet elbow for supply to the Traction Engine tank. The ball on the end of the pump handle is 1/16" (1.6mm) diameter- Hose hooks are 0.010" (.25mm) shim steel annealed for drilling and bending, then re hardened and tempered to spring grade. Screws are 14BA- Finally got the wheels done last night and are retained by blind 'Top Hat' caps with a cross pin, as per the full size. Pins are 3/64" (1.25mm) - Going to be a shame to cover this in paint

Ok Norm, I'm not the world's expert on wiring, but I got it right twice on WH rewires., I reckon if you have the right type of switch?, you have a constant live supply to the Solenoid through the switch when turned on, this constantly makes your starter turn, so the wire must be on the wrong blade on the back of the switch. At least the Solenoid is working ok. If you have no safety switches (Seat, PTO, Pedal), then the Red wire goes from the 'S' Blade on the back of the ignition Switch directly to the small terminal on the Solenoid. The Ammeter is showing - (minus) amps because the constantly running starter motor is drawing the current that would normally be recharging the battery. Check the Ammeter is correctly wired Pos & Neg though. Looking at your pics, I see an awful lot of red wires which will be very confusing to you if someone has messed about with the colour coding. Here is an amended diagram to reflect the absence of a primary safety switch (one left in to represent the PTO switch)- The 2 wires (shown dotted) from the Alternator (may be grey or purple) can be transposed on the Rectifier as the supply is AC. The output through the Orange wire to the Ign Switch is DC. Ignition Switch is earthed through it's body and is essential for the ammeter etc to work properly. Keep at it.

Hi Norm, You don't say what model it is, so I presume it's 1980/81 which uses a 3 position/5 pin 103990 Ign Switch. I've handed my C-120 Info on to Roly with the Tractor, but checked for comparison using parts list. This diagram should be identical for you to check yours- The solenoid may look non serviceable, but I only needs 4 rivets drilling out and replacing after a clean out. Covered it in my C-120/Raider update if you want a link?. Hope it helps. Edit - 103990 switch pins are marked- S- Safety Switch/ Sol Start. R- Rectifier. A- Accessories (lights). I - Igntion (poss via seat safety switch) . B - Battery/Ammeter .

Wick is usually raised and lowered by a wheel that grips the wick. The top section of the burner should lift off of the fuel tank to expose it and replace the wixk when necessary. A picture would help?. A bit older than your heater, but relevant -

Thanks Ewan. I fancied a change last few weeks, as it has been a bit cold. So I turned my hand to learning to steam bend and shape some hardwood for the shafts, even though I'm making a steel framed drawbar to connect to the T/Engine. The shafts came out well as a matched pair and have nearly finished all the 'Ironwork' fittings which were a bit fiddlely to shape in a small size- I'm a bit slow on the tank work, as I need to plan the stages before I begin to rivet/solder up the sections......then there is Xmas!.

I prefer to always log off from Sites/Forums and clear all history+ other data after disconnecting Wi Fi every time. Never had any log in issues anywhere using windows7 and Googy Chrome. I'm not clear on the 'Always Logged in' situ. Can't get my head around it, as if someone says they always remain logged in to a Site/Forum, why does it not show the Username on the 'Who's Online' section at the bottom of the Home page?. Some Forums I use automatically drop you out after a period of inactivity. Then again, I am maybe over cautious. I hope the cause of the problem is able to be resolved and explained.

Looks like you've nearly 'got it nailed' Ian !.