Jump to content
Stormin

Wheel mod.

Recommended Posts

Nice work Norm, yeah cleaning wheels up has to rank as one of the worst WH jobs to do!!

 

I had clearance problems when I fitted the big AG's to my ole 312 years ago.. Had to raise the fender pan by an inch and cut n shut the foot plates to make the tyres fit..

 

The wheels look great by the way :thumbs:

Share this post


Link to post
Share on other sites
21 hours ago, Stormin said:

  

 

DSCF0010.thumb.JPG.541fc80e298ace8aca9c971c281025a3.JPG

 

   By 'eck! :o Wasn't expecting that much difference. 3-1/4" difference.

 

  That throws up another problem. Getting enough ploughing depth. Maximum I will be able to get is just over 4" deep. Could be another addition to the Black Horse topic.

 

  The VHGMC horticultural ploughing rules state a minimum depth of 12cm. Just under 5". Not that I'll be taking part in any of their matches. My tractor and plough don't qualify.

  I put the tractor up on the lift and with the plough hanging over the end, board lying along the lift and plough down, the above depth was ascertained. Now the actuator that does the up and down business, has no in between position. It's either up or down.

 After much trial and error, the tool bar has been modified. The tongue that goes into the slot hitch has been raised so the tool bar is lower. It was also extended and now has two holes for the slot hitch pin. First hole is in the same place and the second an inch back. This has given me two positions. The first hole gives just over 12cm and the second just over 13cm.

  That'll do for now and the test  will be the Hethersgill Vintage Club ploughing match next month.

 

 

Share this post


Link to post
Share on other sites

 

I've already said I'd altered the tool bar as in photo below.

 

DSCF0014.thumb.JPG.f1df586f1079b205b6d2fc51e9cb31e3.JPG

 

  Today I rigged up a way to put a bit more weight on the plough. Dumb bar weights and a big piece of threaded bar.

 

DSCF0015.thumb.JPG.b84289fc6361caf775016f093c81baa7.JPG

 

  I'm going to try with just two of the heavier weights, then may add the two lighter ones.

Share this post


Link to post
Share on other sites

  A bit more in the Black Horse saga.

  As previously stated, after fitting the narrow wheels and tyres, the rear end was sitting higher, resulting in a reduction of plough depth.  So to level things up I'm doing a little modification to the front end.

  My idea is to extend the vertical stem of the steering arms that fit into the front axle. I have a pair of arms off the Raider 10 now a parts donor.  

  So the first job was to re-thread them 10mm. Reason for that is that I've only 10mm bolts long enough. I then turned up some sleeves the same diameter as the steering arms. These I made longer than I may need to allow for final hight adjustment.  I also turned up a couple of spacers for under the axle to raise the front.

  The next job is modifying the trailer stub axles I've got, the same as I did when fitting the scooter wheels earlier in my C-120 thread.

 

 Photo is of parts so far minus bottom spacers.

 

DSCF0001.JPG.dd9b4552e07c578108b355212ed5dcf9.JPG

 

 

 

 

 

Share this post


Link to post
Share on other sites

  As Chris pointed out, I made a bit of an error with the arms. Today I set too to correct it. But how to drill holes in the other ends accurately?  I don't possess vee blocks. Can't do them in the lathe. So I had to think of some other way.

  I finally did them as below in the photo. Wasn't exactly easy keeping things square, but taking my time things came out OK. I used one of the extension sleeves as a guide for a drill to spot the centre. Then I drilled the spindle using three different sized drills, finishing with the tapping size.

 

DSCF0002.JPG.22eb6aaecfa2aa217d47b9edc31dd87c.JPG

 

  Next the holes were threaded 10mm and the stub axle on the arms cut off to 3/4" long. See photo below.

 

DSCF0003.JPG.5530297682d6d818ab4b5fce6d6223e1.JPG

 

  The next job was to shorten the trailer stub axles to 1/2" long. Cut them down to 5/8", then into the lathe to be faced down, drilled and bored out 3/4" I.D. x 1" deep.

 

  Below all ready to weld up.

 

DSCF0004.JPG.82c22046bd92fc6b21ce30f163e83b45.JPG 

 

 

Share this post


Link to post
Share on other sites

 Got the arms finished and fitted this afternoon.

 

5a3a90e919505_DSCF0006(1).JPG.34527a282efc41188c1838bb463583fa.JPG

 

 Wheels are back on and raising the front by 1" now gives a plough depth of 6" or 7-1/4". Depends on the position of the tool bar in the slot hitch below.

  Bar fully in and using the second hole gives the 6". Using the first hole, the one at the end, gives the 7-1/4".

 

5a3a90f09971c_DSCF0007(3).JPG.3a0e5c8af7cce7ca19e8714315a553e1.JPG

 

 Next job is to fit a depth wheel to the plough.

 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


Premium Theme Designed By IBTheme.com

×