JUST O&R

Sound good to me. found this on ebay whats wrong with this picture

I sent him some small ball's Friday that's all I had ( got to get my pants out of my wife's pocketbook too)

Send a peace an I will tell you what I think. or just make the call

Do be leave this We just become experts I did not know it was that easy!! If only David could see me now

Sorry been gone all day I'm also in just let me know what you need to get them done . I also have a couple of those gasket's if you need them. This project will run me about out think there's three left in the goody bag. induction case I have 1. This will be a problem very soon. LET ME KNOW AND ILL SEED SOMEONE SOME $$$$ TO GET THIS SHOW ON THE ROAD!!!!

I know talked about this before but did anyone figure out what gasket material to use for the A-13-18 induction gasket and the 5-6 feather valve gasket?

Got the cylinder off I will need to dig out a used one this is just to far gone. found a good downer.

I will used 00 gear grease very thick so it will not leak out . just ordered a drill chuck for it so I have one . 5/8-16 chuck will fit . In my spare time I can drill holes This gear box had oil in it so just going to make a gasket and put it back together.

I know what you mean my wife's nose is like a cat. She can smell something when you talk about it .The new house will need a detached garage. (hell I'm in the dog house most of the time anyhow ) what are you going to do with all that junk!! (retirement plan just need to get more) Although the kids today have no interest in this stuff .

That looks like it works good no bad smell in the house ether. if you wont to do a little in the house. If I brought one of these in the house I would be shot. that why I work on them at the shop.

For some strange reason I figured it was you!! If you are the some as me I check ebay 4 to 5 times a day.

That Thats going to be a nice fan

I have the auger bit and the end is threaded . it now in peaces all over the bench. that's a good looking auger you have there now I know ware to get parts

Gas tank is aluminum I think the paint is ok I will know in the morning it will be all over the bench in little peaces .yep tank will look good Will need to paint the recoil.

The chip-a-saw is almost done just weighting on one baffle that Clint has on the way. I want to thank him for that again. Got this wards auger about a year ago and now I will clean it up and make it run again. The good thing is its all here baffles,muffler,air filter, so hopefully it wont be bad . It does need a lot of cleaning . I hope this one goes a little better then the last one. I have reached my limit on pictures cant seen to put on any more .

Ok witch one of you got the manhole fan?

That's why they call it snail mail. Glade to see it on the way

Brake fluid will swell rubber to just don't leave the seal in there long or it will fit your ridding mower.

I could use some baffles if you have any.

A set of baffles would be nice I have a few more that are missing in action. Maybe a few diaphragms I'm getting low on them any thing else you could use before I send this out. Clint what about you any thing you need how about anyone I'm willing to do some horse trading

Have 6 of the arm springs I can send 2 I have 3 mufflers # 122-1 #122-2 # a-11-13 Can send you 1. Also have muffler bolts in I think 3 to 4 sizes and extensions and have 50 - 1/32 balls

I will go along with you on that!!!

I have a bag of 50 of each of the balls . I have some carb arm springs not sure how many. I will look Not sure on muffler I will check they are like the air filters and heat baffles they take them off and there gone.

If there is something you need just let me know (same thing a lot of and none of others ) wont run out of diaphragms any time soon thanks to clint!!

looks great!!! That's what I should do I get them running then take the carbs back off and clean out the fuel. Try not to move the needles or change anything. So there is two tapered shafts one short and one long and the keys don't make any difference?