NOS and or Used parts trade

[CNew 404]

Just took a peak at the parchment baking paper soaking in the gas and so far no visual changes. I’m going to leave it in there for a couple more days. I may also try to remove it and heat it gently just to see if it reacts at temperature after soaking in gas (I’ll do it over a bucket of water)...

[JUST O&R 237]

You might want to take it outside. should i call the fire department and let them know where you live?

[CNew 404]

I wonder if something like this might work for the cylinder gaskets?

https://www.garlock.com/en/products/style-9850-high-temp-gasketing

[JUST O&R 237]

Look like they made use one to try.

[CNew 404]

I found another material that looks interesting, FMI 280.

https://www.aspseal.com/pdf/FMI_Non-Asbestos_Gasket_Material.pdf

[JUST O&R 237]

That looks interesting!!    Looks like they make it from .5 mm to 5.mm

Also looks very durable. The gasket in the picture look like there for chainsaw

[JUST O&R 237]

Just got done playing with gaskets and the material Clint sent .

5-6 reed gasket seems to be .005

5-5 induction gasket seems to be the same .005

Now the 200470 reed gasket seems to be .017 13b engine

I thing your rite that gasket paper you have  should work fine I don't think + or _ .001 would make a difference. 

I thought that reed gasket was thinner but not by much.

Cylinder gasket 5-14 is .040 give or take

Cylinder gasket 5-15 is .030 give or take

Muffler gasket  5-16 13 .040 give or take so it could be cut out of the center of the 5-14 to save waist

 

[CNew 404]

FYI, I sent Eric a note letting him know we are interested in the induction case gaskets.  I’ll let you know when I hear back from him.

 

Now to find a source of the gasket material for the cylinder head gaskets...

 

I checked on the parchment paper sample again. No real visual change after soaking for over 24 hrs. 

 

[CNew 404]

Unfortunately I’m not finding anyone that sells the Flexseals FMI 280 gasket material in the 0.03 range.  Seams 1/16 or 1/8” are the common thicknesses for that one. 

 

I did find this other material from Thermoseal (C-4401) that might be a candidate and it’s more readily available in 1/32”.

http://www.thermosealinc.com/products/sealing/by-product/klingersil-c-4401

 

Thoughts?

[JUST O&R 237]

If this was easy everyone would do it . Keep up the good work.

if you need samples of anything

i have all of them. 

[CNew 404]

I found this site and it looks like they carry a few styles in smaller sheets. Might be worth getting a couple to 15x15” pieces to evaluate. They have at least 4 styles that seem comparable.

 

http://www.equalseal.com/garlock-3000-blue-gard-gaskets-sheets-s/2037.htm

[Wallfish 698]

On 1/27/2020 at 1:52 PM, JUST O&R said:

Muffler gasket  5-16 13 .040 give or take so it could be cut out of the center of the 5-14 to save waist

where does this gasket go?

Never mind, found it on the older engine IPL for the muffler. Don't remember seeing a gasket there before but I haven't played with them for a while.

[CNew 404]

I still don’t know what this gasket is, didn’t know there was ever a muffler gasket.

[JUST O&R 237]

I'm glade you found it I was just about to put a pic on here to help well maybe I still will # 73 on the diagram.

most don't have them but some do Ive  been putting them on most all of them.

Ohlsson & Rice Compact I II III Engines Parts Nov 65(1).pdf

On 1/26/2020 at 8:53 PM, CNew said:

Just took a peak at the parchment baking paper soaking in the gas and so far no visual changes. I’m going to leave it in there for a couple more days. I may also try to remove it and heat it gently just to see if it reacts at temperature after soaking in gas (I’ll do it over a bucket of water)...

Did you ever fire it up??

[CNew 404]

Ahhhhh-haaa, I never noticed that little gasket before. Interesting, maybe I’ll start adding those as well.

 

Ha, yes I put a gentle flame under both and eventually they do ignite. It wasn’t the most scientifically controlled experiment....

[CNew 404]

Just heard back from Eric. He’s up for making us some gaskets, just need to send the NOS gaskets along with the materials.  I mentioned to him we’re also looking into the cylinder head gaskets once we identify some good material.

[Wallfish 698]

15 minutes ago, CNew said:

just need to send the NOS gaskets along with the materials.

NOS gaskets are in the box I sent you with the vertical tank you needed. Also sent a piece of the baking paper I have. it's even the right color but might be too thin.

[JUST O&R 237]

let me know  if there  is any thing you need and will get this done.

Do you have a 5-16 gasket to send or do want to let to let those go for now? there not relay  important . 

[Wallfish 698]

1 hour ago, CNew said:

I mentioned to him we’re also looking into the cylinder head gaskets once we identify some good material

Crap! I shoulda sent some of those too. Plus Eric is very good at finding the correct material too. He found the mylar? plastic we used for those check valves.

[CNew 404]

I think I’ve found a couple materials that might work.  I just need to order some samples.

[JUST O&R 237]

Do you need some $$$

or the cylinder gaskets

[CNew 404]

Not yet, once I figure out if the material will work I’ll get with Eric to see what all that will cost.

I don’t know yet what it will cost for him to make the induction case gaskets yet either.

[CNew 404]

I just ordered a piece of Garlock 2900. looks like it has a fairly long lead time before it ships.

I may also look at getting a piece of Garlock 3000 and a piece of Thermoseal C-4401.

[JUST O&R 237]

Just let my know.!!

[CNew 404]

Will do.

It’ll be nice if we can finally get this all figured out and have a source for these induction and cycling we head gaskets.