tvenetis

I am working on a chain saw and had to take the handle apart to fix the throttle cable. I can't figure where the spring on the throttle cable is supposed to hook to. I figure one end goes around the cable on the trigger and there is another end of the spring is bent at a right angle and has a long straight end but where does that go thanks.

On the gasket that goes over the read valve which is supposed to seal the cover can you use a o ring instead?

When you use a sharpening stone to make it thinner how do you hold the key.

I am replaceing a coil on a ohlsson engine but how do you feed the wire around the cylinder to put it on the stud thanks.

I had a friend help me pack the needle bearings on the connecting rod where it goes on the crankshaft and that was not easy. I wish there was a easier way to position them on the connecting rod.

For anyone interested I have a Ohlsson & Rich chain saw which I repaired and got running for 300.00 and I alson have a ohlsson hedge clipper which I got running for 300.00. I have a picture of the chain saw and will try to get pictures of the hedge clippers.

Thanks John on the carburetor arms that have the rubber on it if the rubber is bad can I put a ball in the hole like the older carbs?

I realize that but the small line might fit on the carburetor tighter.

I have some of that thing gas line that ohlsson sold how do I soften it up so I can use it thanks.

Yes I did it before but now the screen came off the connection inside the tank.

On the engines with the gas tank on the bottom how are you supposed to replace the filter in the tank.

thank youHi Bonnie do you still have ohlsson parts for sale thanks.

Hi Bonnie do you still have ohlsson parts for sale thanks.

The carburetor assembly I am working with has a rubber that was on the lever. Can I put a ball in the hole because the rubber fell off the arm?

I am trying to put the diaphragm assembly together and I showed a friend who was helping me and he thinks it will still work without putting the small pin in the groove. He said it still pivots correctly with out it what do you people think thanks.

John is this the right circle cutter https://www.amazon.com/LION-Ev-R-Round-Perfect-Diameter-C-1500P/dp/B00JDTTIWU/ref=asc_df_B00JDTTIWU/?tag=hyprod-20&linkCode=df0&hvadid=167119535166&hvpos=&hvnetw=g&hvrand=17646031234062017995&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=1023285&hvtargid=pla-306673532351&region_id=373786&th=1

I am trying to put the air filter on and I hold it flush with the carburetor but when I tighten the nut it wants to turn and the flang on the aircleaner does not stay in the carburetor.

thanks John what is Parchment paper and what is the jungle site. jungle.com does not come up thanks.

Does any one know there to get ohlsson engine gaskets like the one that goes around the read valve assembly and the round gasket that goes over the read valve assembly before you put the case together?

I put another read valve in and got it running. Thanks for all the help.

I think the problem might be in the read valve. Is there a way to take them out and clean it?

the spark is blue and it turns easy with plug out just compression. For some reason it won't fire and plug is new. I tried different plugs also. I just tried the chicken power flywheel and recoil on another engine and that other engine runs with those changed parts so I know it is not the flywheel coil or condenser. The compression is 110.

It has compression and spark but it bearly pops when I spray a little fuel in the carburetor. I have another engine and as soon as I spray fuel in the carb and pull the cord it runs for about a second like it supposed to. I even switched coils from the engine the runs to the chicken power and same problem. I am going to remove a metal head gasket and see if that helps. I removed a metal head gasket and it has 110 compression but it won't fire. I remember I put the crank shaft the flywheel side in because the original one had the threads broke off.

Hi Joe do you still have parts left thanks.

On a chicken power engine I am wirking on I put new rings and it has compression but the recoil seems to pull harder than most. It tries to start but won't keep running and the carb has been clean and great spark. I was thinking of taken off the gears which are greased well and see if that makes a difference. Do all those engines pull hard it is a 13b thanks. I took off the gears but did not make a difference. Maybe some one changed the flywheel. Are there different flywheels for ohlsson engine maybe timing is wrong.