Jump to content

Leaderboard


Popular Content

Showing content with the highest reputation on 06/13/2021 in Posts

  1. 4 points
    .........If anything.........That was the issue I was asked to sort out recently. A heavy bronze carb fitted to a small water cooled 1/2hp engine from 1923 and had been adapted to fit onto an early 1930s Lawnmower!!.- I actually found a Manual and parts list for the engine, but of course not one single available spare part. Failed to find anyone else online familiar with, or who had a similar ''N' type engine made by Stuart Turner. Several bits missing according to the parts list diagram and one item had fortunately been acquired from ebay...the all important Float Bowl (screw on) Lid. So I had to make and find the bits etc, so as it had not run for god knows how long, it was dismantled- Certainly overdue for a clean and repair. The small clip under the spring (bottom middle of above pic) should be fixed by solder to the float. It holds the needle at correct height.........duly fixed. Established that the large hollow brass nut (top left above) which acts as a sediment bowl should have a screened filter and a spring within. items (on left of next image) 4044/4045- The bits had to fit within these parts- So after a search for materials, a bit of lathe time and some soldering, I had the 'makins' of the necessaries- The 'Stove Pipe' top hat filter body was silver soldered together, so that I could soft solder the mesh to the bottom and sides. But not before it was subjected to some careful milling to put some 1/4"wide slots into the side wall. Appears to be some distortion in the image below which makes the filter body look crooked, but assure it is not. - I was lucky to find in my stock, a suitable spring to apply pressure to the filter and keep it all in contact with it's seat. That filter/sediment body nut is 1 inch A/F. So all done and ready to bolt on. Now super clean inside and favoured the patina to polish on a motor of this age- Oh and yes, I have the task of getting this thing running/working, along with another pile of broken rusty bits......I may be some time!. Regards
  2. 2 points
    rolloman 1

    A Little update on my Tractor

    Hello all Some of you will remember my Huttenwerk Tractor which i had on here, well I have been busy overhauling the Tracks starting with the track plates then new rubbers and bolts , And today the track cover plates were fitted 50 off factory made from 1.6 mm mild steel then drilled and painted Matt black . and to finish 200 coach bolts washers and m8 nuts all to be tightened up. Then over to the wash and clean corner this now runs so well now i can hardly believe it hope you like i think it great
  3. 1 point
    Ian

    Southbend Lathe Tool Holder

    Grab a lump of ally.. Bung it in the lathe and face the end off. A bit of a trim down the side. More metal removed, the black pen stuff was to help me get the right shape.. Or near enough.. Almost there now.. Parted off. Then finished off... HHmmmm.. Shiny To fit the knob thingy I had to drill yet another hole.. Tap a thread in it. Ta Daaa... Almost.. Not sure about the thread showing.. A bit of ally tube soon had the looks sorted.. And finally fit the finished tool holder to the lathe.. I hope you all have enjoyed this little build, it was quite fun to make Of course..... This build comes with a video
  4. 1 point
    Ian

    Southbend Lathe Tool Holder

    Now for a errr... Interesting challenge.. How to cut a smallish square from that big slab! The best and quietest way I could think of was a bit "iffy", but it worked.. That looks very close!! But it clears, just.. Lot's of cutting and turning later, all three parts are the right size. A quick look at my plans... Or should that be rough scribble? And it was time to fix all three parts together... A single bolt kept it all in check.. So I could mark out and start drilling holes to put some bolts through. Here's the top drilled out.. And the base... A bit of countersinking was needed.. So the bolt heads would sit flush. More to follow later including a rather well edited if rather long video... Tune back for more later..
  5. 1 point
    pmackellow

    Tinkers Park Steam Rally June 5/6

    Our local event so popped up for a look this morning Not much horticultural but one or two machines of interest...
  6. 1 point
    Maxwell-8

    Garden tracor meme

    I am 19 years old and always working on garden tractors. People my age are always spending time with their girlfriend. The other day my parents came asking if I had met any nice girls and if their was a girl I liked. I replied with only this picture:
×
×
  • Create New...