factory 487 #26 Posted September 20, 2019 Did you buy it then? David Share this post Link to post Share on other sites
CNew 404 #27 Posted September 20, 2019 I never saw it either. I check frequently on a daily basis. I’m surprised this didn’t show up. Share this post Link to post Share on other sites
factory 487 #28 Posted September 20, 2019 56 minutes ago, JUST O&R said: One fin broke on flywheel and no recoil I have plenty of them. need to put the rite tank on it I don't think that's the rite one? doesn't look like it was used much. I hope it's as good as the pics. Just re-read the post, you did buy it, good to know it's going to someone on here and no that's not the correct tank, it should be attached to the engine as they usually are, maybe whatever damaged the starter & other bits finished off the tank too. 46 minutes ago, CNew said: I never saw it either. I check frequently on a daily basis. I’m surprised this didn’t show up. Maybe you didn't see it because it sold in less than a day. David Share this post Link to post Share on other sites
CNew 404 #29 Posted September 20, 2019 Yes, I’m also glad it landed with someone on here- nice grab Just O&R! Looking forward to great photos as you start to get’r all fixed up! Share this post Link to post Share on other sites
JUST O&R 237 #30 Posted September 20, 2019 ya i got it. I said I need to look harder. just seen it on ebay and he was willing to ship It looked good to me need to change tank dig up a flywheel and recoil and she should be good . looks like the rest is in good shape. I will let you know. Share this post Link to post Share on other sites
factory 487 #31 Posted September 20, 2019 It definitely has a piece broken off from the magneto plate (see near the exhaust), the engine mounting bracket looks to need straightening to re-align the drive pulleys too (see picture from underneath) and you will need a carb, but they are easier to find than parts for the board itself, good luck with the restoration. The listing does have some good pictures showing the throttle linkages. David Share this post Link to post Share on other sites
Mekash 2 #32 Posted September 20, 2019 (edited) Do you mind me asking what price you paid for it? Please pm me if you would like. Edited September 21, 2019 by factory Email address removed to help prevent spam, it's best to send contact information by personal message (PM). Share this post Link to post Share on other sites
Webhead 95 #33 Posted September 21, 2019 Looks like he paid 250. Is yours for sale, minus the cat? Share this post Link to post Share on other sites
JUST O&R 237 #34 Posted September 21, 2019 Yes paid 250. I think i have what I need to put it back together. the only thing I'm missing is the tank bracket. Don't think I have that style but I could install a new engine and use the old one for parts. (Will fine out next week) Share this post Link to post Share on other sites
factory 487 #35 Posted September 21, 2019 Is that NOS engine a Model J? If it is it should bolt straight on, you will only need to transfer the pulley over from the old one. 13 hours ago, Mekash said: Do you mind me asking what price you paid for it? The ebay link with sold price & pictures was provided by the seller in post #23. https://www.ebay.com/itm/264471736014 David Share this post Link to post Share on other sites
JUST O&R 237 #36 Posted September 21, 2019 Not sure its been up on the shelf a for some time I need to get the ladder out. Gear box looks the same that would make it simple . Share this post Link to post Share on other sites
JUST O&R 237 #37 Posted September 21, 2019 This engine is an f 09725 so we will need to change the gearbox . Share this post Link to post Share on other sites
factory 487 #38 Posted September 21, 2019 The Model F is the same gear ratio as the Model J but without the Clutch, I think a digit in missing from the serial number as some of the parts look later than SN #09725. David Share this post Link to post Share on other sites
JUST O&R 237 #39 Posted September 21, 2019 Your rite I missed a number ser # is 097295 and Your rite the f model has no clutch. I'm not sure but I hope the gearbox will fit ? I'm going to try to find the parts first I would hate to take a complete engine apart. If it comes apart it will never be a nos engine again. thanks for the help David. Share this post Link to post Share on other sites
factory 487 #40 Posted September 21, 2019 That number looks right, with a production date of approx 1965. The gearbox will fit fine, the only differences inside are the gears attached to the engine PTO shaft, the clutch & drum gear changes to a standard gear (see parts circled below), all the case parts are the same for both gearboxes. Hopefully you can find the parts to repair the Model J, for the missing tank bracket you could make a temporary one & swap it over if you find an original. David Share this post Link to post Share on other sites
JUST O&R 237 #41 Posted September 23, 2019 Quote This is something I did not know . http://ampoleagle.com/a-dunkirk-legend-in-the-making-p2615-146.htm https://en.wikipedia.org/wiki/H._B._Halicki Share this post Link to post Share on other sites
JUST O&R 237 #42 Posted September 28, 2019 Got the toby cart yesterday board looks great bracket for engine is bent. I think it will straighten up. got the engine off got it apart now were waiting on the tank bracket should be here Monday This should not take long ( I hope ) I would like to take it for a ride. 1 CNew reacted to this Share this post Link to post Share on other sites
CNew 404 #43 Posted September 28, 2019 That Toby Cart looks really nice! That should be a cool ride whe you’re done, have someone take a video of you on it! Is there any sort of brake or do you just drag your feet? Share this post Link to post Share on other sites
Wallfish 698 #44 Posted September 28, 2019 18 minutes ago, JUST O&R said: I would like to take it for a ride. Please don't forget the video! This is gonna be fun for us too! Share this post Link to post Share on other sites
JUST O&R 237 #45 Posted September 29, 2019 No brake dont know how you stop . just jump off Share this post Link to post Share on other sites
factory 487 #46 Posted September 30, 2019 On 9/29/2019 at 12:03 AM, JUST O&R said: Got the toby cart yesterday board looks great bracket for engine is bent. I think it will straighten up. got the engine off got it apart now were waiting on the tank bracket should be here Monday This should not take long ( I hope ) I would like to take it for a ride. I noticed that it was bent a few posts back, as the two drive pulleys weren't lined up straight in the sellers pictures, also the frame for the back rest is normally mounted underneath the board. I do wonder if the original owner had a mishap with it, anyway good luck with the restoration. David P.S. Are the links in post #41 meant to be in the empty quote box? Share this post Link to post Share on other sites
JUST O&R 237 #47 Posted September 30, 2019 No the link in post 41 were just something I did not know. but as i go back and read the hole thread I now see that this is a given . sometimes I just read between the lines. Share this post Link to post Share on other sites
JUST O&R 237 #48 Posted September 30, 2019 David you are rite I was just looking back threw the pic and all of the other boards have the backrest mounted under the board. The backrest on this board has new screws so someone has changed it. good eye thanks I will fix that This is why your the factory. thanks terry Share this post Link to post Share on other sites
JUST O&R 237 #49 Posted October 1, 2019 Just looking at all the pic's again but don't see any of the linkage that goes to the carb Does anyone have a pic of the linkage going to the carb? or is it a cable ? Share this post Link to post Share on other sites
factory 487 #50 Posted October 1, 2019 Perhaps they had to move the backrest to raise that extra large gas tank up a bit. Usually the throttle control is via a small diameter Bowden cable, fitted to the lower set of holes on the side of the carb, sometimes you find a lever added instead for RC modified engines. Most of these Toby Cart's seem to be missing the carb, hopefully someone can confirm what was fitted. David Share this post Link to post Share on other sites
