Leaderboard

For the last few months I have been medically chair bound with the exception of odd forays to the garages and workshop to find things. Father Christmas was very good to me giving me a comfy office chair, an LED head torch and a Drill Doctor drill sharpener. My new lockdown past time is sitting at the kitchen table in my comfy chair ,my headlight beaming away and my drill sharpener on the table in front of me. Over 50 years of workshopping I have somehow amassed a huge collection of drill bits , some were my Father's , Rhys gave me a pile of Morse tapered lathe drills but most I have bought when embarking on a new project. Although I am quite capable of sharpening drill bits ,it has not been a regular workshop maintenance task and consequently it was quicker to buy some new drills rather than sort out and sharpen old ones, UNTIL NOW ! The drill Doctor machine will cope with drills from 1mm ( if you are careful ) up to 3/4" . The drill bit is set in a chuck which aligns the flutes to produce a point angle of 118 - 135 degrees with minor up or down variation. The chuck is then slotted into a holding socket above the diamond grinding wheel to be rotated slowly by hand, two turns will dress up a tired drill to new, 10 turns will restore a broken drill. The machine was not cheap but works extremely well, will cater for split point drills and masonry bits, clean working ,not too noisy and a nice way to spend a few hours in the warm recycling useful things. I would certainly never have stood at the grinder for many hours hand sharpening hundreds of drill bits. I have now ordered a couple of graded drill bit holders so that I can again sit at the table and sort out all the sizes and then give a couple of sets to my sons. I recently bought a spring caliper guage for measuring valve shims and was very pleasantly surprised to find that it can display in mm / inches and also fractions of inches so I can now identify some of the odd sized tapping drills I have. That should take up a few hours maybe I will improve my set up with my headlamp and some wireless earphones tuned in to Planet Rock!

This advert for the smaller aero engines arrived today all the way from the USA Now framed and with the display...

Got a drill sharpener myself, though I doubt I would get away with using it in the house. Workshop is a bit chilly for working in. With the lockdown restrictions, my farm work and trips over to Scotland are curtailed. Jigsaws have been rooted out. More books read and a daily 2-1/2 approx. mile walk round the block. I'm even doing the washing up. Sometimes!

That turned out great!

Thank you. My brother's first car in the early 1960's was a 1935 Morris 8 tourer, YS 5104, followed by a 1936 Ford model Y. If my father hadn't had a spare fiver in 1963 I wouldn't have the car now and there were a couple of times I thought it was going to go belly up and I'd have to sell it for spares but I got there eventually.

I bought a basic Martek Drill Sharpener back in 1986, attaches to an electric drill and fixed into a drill holder back in that period. Only covered bits from 1/8" upwards. Still have it, but not used much. I tend to dispose of, or sharpen by hand, any bits under 1/8" and use only for wood after. Although I was successful in hand sharpening 2 off 1/32" drill bits after I broke them while working on my latest project. To be on the safe side, I started the hole with a good one, then followed up with the sharpened one and went fine with no issues. Winter 'clips my wings' with projects due cold workshop and other priorities. Like you're having to do, I do much of small work on the table in the warmer conditions. The other thing keeping me busy is learning the secrets of a different OS from Windows to MacBook Pro after 15 years using Microsoft.

With the under dash wiring done I could now finish the carpeting of the bulkhead, side panels and floor. When I initially started in 2006 I removed the gearbox cover which was made of moulded hard rubber and had broken in 3 pieces but I was going to make a mould from it and do one in fibreglass but in the meantime it had fallen off a shelf and was now in a hundred pieces. A modified one was made from aluminium and made it a lot easier to carpet. The vinyl edging around the carpeting is wider than I would have liked but the rubber backing just cracks and the carpet splits if you sew too close to the edge, I didn't have this trouble with the hessian backed stuff I used on the Carlton. The bulkhead and the side panels with air conditioning facility - no fuses required! then renovated front seats fitted The new front brake cylinders and shoes along with the new hubs and bearings were next The tyres were all different makes and sizes and well over 50 years old so new 5.50 x 16 Blockley tyres tubes and tube protectors were ordered, the wheels sand blasted and powder coated to prevent damaging the new tubes. The original colour had been cream then repainted yellow and I couldn't decide whether to go black to match the body, green to match the interior but in the end decided to go with silver. Not far to go now but we still have the engine saga.

Finally got around to cleaning up the Aquabug cover that my mate got mended for me Its now in the display next to the machine, I still think it looks better without the cover so am leaving it off for now...