Picked this up today and was told it’s for wheelhorse it looks like a toolbar attachment it has a rake on it at the moment . Anyone have any info or know if it is or isn’t wheelhorse?
Yes I had discussions with the owner and bought it.. thanks for the info and offer of the manual I would certainly appreciate that...
Yes I tried speaking to the owner but got no reply . I was very interested in buying it also . I’m pleased it’s gone somewhere it’s going to be appreciated 👍 as soon as I get a chance I’ll send that manual over .
This is the same as mine . It was made in 1986 for one year and only distributed in Europe the engines a robin Subaru lump I have a manual somewhere I can email over to you . Is this the one that was recently on eBay ?
Many thanks for the advice and help . The cobalt bits are now my new best friend. The new collar is on its way 👍 tonight when I get in from work I’ll put it in the chest freezer I turned on last night . I’ve ordered the graphite penetrating oil as I was using wd40 . All of the pin is now successfully drilled it was the pin with a bolt bashed into it to spread it out 😡 once I’ve tried the freezing I’ll also try a little heat from the oxy/acetylene. I’ll keep you updated on progress.
I think I’ve got all of the pin drilled out (cobalt bits are my new best friend)
my next question is I can’t get it to separate. The plastic moulding I’m pointing to with the screwdriver am I ok to take that back until I can see the top of the shaft and use a drift to get it moving ? Or will this knacker the steering wheel?
Got a bit more in depth with it today and the roll pin and collar grub screw . The roll pin is solid but I’ll drill it to save damaging the steering wheel . The collar is 100% a sheared bolt as the grub screw must have been lost . Does anyone have a spare collar the want to sell ? Then I can just cut this one off .
You'll need to get the steering wheel off the shaft which is held on with a rollpin, knock that out and give it a good soaking with a penetrate.
The collar has an allen screw holding it in position and sometimes a job to undo, might need warming up to undo it
I’ll get a picture of the top tomorrow it looks like a rusty bolt that’s had the head sheared off . The collar pictured don’t have an all key for it it’s flat as if it had a bolt head on it at some stage . It’s annoying as it’s the only thing at the moment stopping me getting it all to the blasters .
Can anyone tell me does the steering split at this joint or how to get the steering shaft out . I’m hoping it’s not the removal of the steering wheel as that’s not possible 😟 should this be a bolt ?
Well today I’ve started the strip down of the 512 I’ve found a few small problems that I didn’t know about but they are nothing to serious. Headlights and wiring needs more than just connecting, bottom of the bonnet needs tlc the gearbox bolts that support the rear of the bodywork are stripped in the casing with one being snapped. That’s about it at the moment. Next step is to get it all sand blasted to see what the metals like and get off the several coats of brushed on paint .
They look good, don't often see gang mowers on display
There was a lot of interest in the horse once they were fitted. I’m looking forward to repairing the other two and repainting them . I was thinking of doing the frame and weights wheel Horse red . What do You think?
This weekend has been spent at Merton Vintage Fair and a good first show for myself and the horse . I managed to find a well used but very serviceable 5 gang mower set in the auction and was lucky enough to grab a bargain . Two need a spot of welding but nothing to bad . The other three towed like a dream .
Well after being ribbed at the weekend for using a flymo I picked this 1976? Webb 2hp up on a selling site for £25 . Very pleased with it as it runs well I do need to try to work out how to slow the drive down on it as it takes off a bit faster than I can move 😂
New Build!!! Ditch Mower
in Ride On's
Posted
Looks like it’s doing the job 👍