As most will know, Jonathan, (expeatfarmer), has sold most of his collection of Ransom crawlers. He did have two large Ransom reel mowers. These attracted no interest. So Jonathan removed the engines and made a roller out of one. Another friend of mine bought that off him after I took him to see it. I bought the remains of the other.
Below is what I got plus the handles.
First mod was to trim the bottoms of the sides, so they wouldn't dig in when behind one of my garden tractors.
Next fit the handles. But in front instead of behind to make the draw bar.
Two of the side offcuts were made into plates. Utilising the holes already there.
A pin off the Cabstar tipper I once owned, makes a good hitch pin.
Behind the Sears/Roper ready for a trial.
Worked grand though the roller could do with being a little wider. Width of the wheels. But I can't do anything about that. I can offset it on the Sears hitch if I need too.
Ten minutes after mowing this afternoon, the C-125 spluttered to a stop and refused to restart. Pushed it back to the workshop and after getting my breath back, investigated. Plug sparking ok but dry. Was going to check the points but as I knelt to remove the cover, I noticed petrol leaking from the air filter.
Reached up and turned the ignition key. Engine turned over and petrol flowed out of the carb. Removed the float bowl which was clean inside. Rattled the float up and down, while turning the key and fuel came out. Then gently held the float up and fuel stopped flowing.
Put the bowl back and tried starting again. Engine fired up and no sign of fuel leaking out of carb. Finished 2hrs of mowing with out any more problems.
I reckon a speck of dirt had been stopping the float needle valve from seating properly.
My first job this morning was to sort out the recoil starter on his wacker plate. There was a broken pin inside the mechanism. To cut a long story short, failed to fix it. Reverted to the good old fashioned way of cord round a pulley and got it going.
Ramp in workshop doorway got wacked down.
Put the guttering up on the right hand side of the carport. BTW. A bat has taken up residence in part of the middle truss. Bat droppings on the floor. Some kind of sheet is going to be fitted below where it roosts. Otherwise Fiona is going to be kept busy.
Final job was some work on the Case tractors hitch. It has a missing pin and still has. We couldn't find anything for a suitable temp' replacement.
Not bad for a 32 year old tractor.
Rear gable end of workshop was finished yesterday. Makes the roof seem higher.
Digger has a nice new cab on now, after being hit by the runaway tractor. It was an insurance job and even came back with an air freshener in.
The finished carport. Dunc built the store room wall and fitted the door last week. Guttering down the right hand has to be fitted yet. I thought we'd done it. Plenty of room for the two Volvos.
Workshop when I arrived this morning.
Das, the joiner, soon finished the last bay.
Dunc and I fitted the side rails while Das, started on the left hand side. Dunc fitting blocks to support the side rails.
Used the C-125 and trailer to bring up the service door and frame. Which was then fitted. Front rails also fitted.
Dunc fitting the cricket bats. If you saw them before fitting you'd see why they get that name.
Das fitting the outer cladding boards. He was up and down that ladder all day. Oh to be young.
And before anyone says what was I doing. I assisted Dunc with the side and end rails and kept Das supplied with boards. Also tided away rubbish.
We got the other side finished on Bank holiday Monday. I didn't return till last Friday due to the workshop floor being concreted and other jobs at home.
I went over last Wednesday and found Dunc had done the wall for the store room at the back of the carport and clad the front end. We did fit the barge board to the front and the guttering along both sides.
Back on Friday and more work on the new workshop. Started the cladding at last. While another man was fixing the boards, I placed them handy for him. Dunc and I fixed the back gable end cross beams. Also brought a tractor trailer load of boards up from the field. Loaded and unloaded by hand. Only approx. 160. And by the time I'd finished, that's how old I felt.
Didn't have my camera, but I'm going over tomorrow all being well and I'll get a photo or two.
After mowing yesterday, with the C-125, I found the front right bolt holding engine and wobble plate had snapped. Solid mountings and not the original rubber ones. I noticed a slight gap 'tween spacer and plate. So I suspect the plate isn't quite true. With feeler gauges it was just over 70 thou.
This morning I dropped the front axle and removed the cross bar. The broken end came out easily when the drill bit, bit. So bar was replaced.
I then found a washer that measured 75 thou. That would do as a shim under the spacer after I cut a slot in it to clear the bolt.
All back together now and hope fully no more sheared bolts.
I'd still been having starting problems with the C-125 and yesterday it refused to start. Squirting petrol in the carb mouth made no difference and the plug had a good spark.
I decide to check the points and found they were rather wide. That would throw the timing out. I'm assuming that last time I adjusted the points, they'd opened up when the securing screw was tightened. This does happen sometimes. After about a half hour of setting, tightening, checking, setting, tightening, checking, I managed to get the correct 20 thou gap.
Picked the frame and swinging arm up from the powder coaters this morning. Well pleased with them.
Wheel hubs and spokes got cleaned up Wednesday and finished Thursday. Really time consuming. The remaining paint on the hubs had to be carefully chipped and scraped off. The spokes rubbed down with emery cloth.
Hubs got a first coat of paint this afternoon. Brush painted with one of Carols 3/4" wide artists brushes.
Tot rod
in Home Built Items
Posted
I really like that Alan. I see it's big enough for you to ride round on. And with the box on the back handy for you to do the shopping.