Leaderboard
Popular Content
Showing content with the highest reputation on 11/25/2015 in all areas
-
6 pointsThanks Charlie. You guessed right Koen, it is a Bing.. Hold fire on looking through your carb collection for now, a new carb has been ordered which should arrive today.. Hi James, I knew about the Renault engine, I didn't know the rest of a D250 was Gutbrod! The fender pan is hard work but it's getting there slowly. To see where the smaller dents are I had to strip off the red powder coating which wasn't much fun as it's hard stuff! I gave the back of the pan a quick coat of blue paint and gave it a light sanding back once it had dried.. The blue bits left are all low spots which need to be beaten out.. Slowly the blue bits are going as the pan gets straighter. This is the corner where the big kink was That's enough about the fender pan, now onto an inlet manifold for the new carb.. Lathe work has been interesting due to problems with both Nigel's and my lathes but we got there in the end.. Starting with a bit of pipe being cleaned up. The inside was bored out a bit so it would be a tight fit on the original manifold. Boring out the mounting flange. A taper was cut so the pipe could be firmly welded on. Like so Now that's a nice bead of weld Back on the lathe to turn the welds down and give a nice flat mounting surface.. A bit of trimming, cleaning, welding and painting later the carb bolts on It's a shame the carb has problems but a new one should be arriving today
-
4 pointsBit more progress today. After much holding the ram in various positions, I decided the only place for it was under the fender. So that is where it is. Attached to the rear fulcrum. Lift lever and/or pump can be used. Also the lift lever will act as a lock when hitch raised. Attached to the side of the hood stand. Very convenient hole already there. It is a very tight fit, but nothing catches. The ram does not travel to it's full extent and cut out switches may be needed. I think/hope that should be ok. Just have to suck it and see. I did think the hoses may have been to short, but in fact they are to long. So I'll get them shortened after refitting the pump and motor. Switch to fit and wiring next.
-
2 points
Briggs & Stratton 8fb
Ian and one other reacted to C-101plowerpower for a post in a topic
Bought annother briggs today, annother military one i think looking at the olive drab that's on it. Anyway here's some pics -
2 points
Ransomes trip levers
hpearce and one other reacted to Rocboni for a post in a topic
I have been busy re making latch/trip levers for the Ransomes mg6/40 3 point linkage, these are a must for anyone who has the right and left hand ploughs. Two sets available, others have been sold. Now completely unobtainable £100/ set + postage. -
2 points
Wheel Horse Raider 10 Stolen
HeadExam and one other reacted to adgecutler for a post in a topic
Thanks everyone for the comments and giving this attention, especially to Headexam for sharing it here before I was able too (I wasn't a member). Sadly the 'oss is still missing despite my searching and asking, the children have even turned into superheroes of late and been using their powers in the search! I have become quite obsessed with this and even taken holiday from work to try and track her down but at present seem to have hit a wall, I'm very disappointed with the Police for leaving her there where she was first dumped, besides anything else it was a school route and if any of the children had started her it could have ended in a very messy way. Please keep vigilant, I can name several distinguishing marks besides the obvious. -
2 points
C-120 refurb.
Ian and one other reacted to The Fife Plooman for a post in a topic
Hi Stormin Watching with interest. you are doing well Would it not have been easier buying a Gutbrod 1032 and painting it red HA HA I suppose it is better saying I did it. Look forward to seeing you again Frae the Fife Plooman -
1 point
Briggs & Stratton 8fb
the showman reacted to C-101plowerpower for a post in a topic
It does, poured some petrol down ita throat and it started first pull -
1 pointIt's not ideal, I know but gear levers get in the way of a bar right across. I'll see what happens when tested. I may put a strengthening plate top to bottom or some kind of bracing. When the top plate is on, that will stiffen things up.
-
1 point
C-120 refurb.
meadowfield reacted to Ian for a post in a topic
Nice work there Norm, of course you understand that we need a "first lift of the 3 point with someone standing on the arms" video -
1 point
the showman and me went ploughing today
nigel reacted to the showman for a post in a topic
I told them I ploughed it all mate -
1 pointGot the connecting arm made today. First off I made a cardboard one. This was so I could get the curve right and length. I made arm in three parts. This was to allow clearance when third gear is engaged. Also allowed me to adjust length and position before final welding. Everything seems to work OK, so next thing is painting. Must admit I was lucky. Of the 1"x1/4" flat I had available, I only had 1" left over.
-
1 point
Project Horse Gut....Nigel and Ians joint project
Ian reacted to diggerjames for a post in a topic
it's a good job it's a Renault engine not a VW engine or emissions would be wrong as well -
1 point
Project Horse Gut....Nigel and Ians joint project
Ian reacted to C-101plowerpower for a post in a topic
yep, you're right, the d250 is basically the same as a gutbrod 2500, just a different colour and decals -
1 point
New workshop
HeadExam reacted to meadowfield for a post in a topic
Slow progress, last weeks navigation canal slowed us down. The calm and wet has forced me to this painting in the dining room Missus not impressed, dog keeps jumping up to have a look and gets paint in her paws, then runs off... -
1 pointThe D250 was built by Gutbrod and did have a Renault 850cc engine.
-
1 point
Project Horse Gut....Nigel and Ians joint project
Ian reacted to diggerjames for a post in a topic
Great project boys , the wheellhorse D250 was based on a gutbrod as memory serves with a Renault engine please correct me if I'm wrong . -
1 point
Project Horse Gut....Nigel and Ians joint project
Ian reacted to C-101plowerpower for a post in a topic
what type is the original carb? guessing its a bing? might have a look thru my carb stockpile -
1 point
Project Horse Gut....Nigel and Ians joint project
Ian reacted to Charlie Smith for a post in a topic
loving it! great work guys -
1 pointBit more done today. Modifying the hitch lift system. Basically after much umming and ahhing, I decided on copying Mark and Ewan's mod. (Ride On's. Page 11) So far, spindle, housings and arms made. I did think of fitting bushes in the housings, but I'd no material to make any and I wasn't going to do a 60 mile round trip. I have fitted grease nipples, so things should last me out. I'll have to drill a hole in the fender for access to the LH one. The RH can be reached via the trans filler tube hole. One mistake I did make, was to make the housing securing tabs long enough. The screw and nut are fouling the trans oil filler tube. Not a problem, just annoying. Photo below.